Williston, North Dakota, United States
Williston, North Dakota, United States
Skills: Coil Tubing
Education: High School/Secondary
Employment Type: Full Time Salaried Employee
Location: Williston, North Dakota, United States
In order to apply for this position, applicants MUST meet the following criteria. If your resume does not match these criteria, you will not be able to apply for this position.
JOB DUTIES & RESPONSIBILITIES:
Under strict supervision, delivers PSL equipment to wellsite. Learns basic operations to include but not limited to:
(1) performing pre/post job equipment inspections,
(2) performing and completing preventative maintenance procedures,
(3) maintaining and operating High Pressure fluid pump,
(4) performing hydrostatic testing on Blow Out Prevention Equipment (BOPE) and reels during pre/post job procedures,
(5) monitoring well control parameters during job application.
Completes requisite training (essential math, essential red book, safety training, etc.) following iLearn's career development system processes.
Assists in assembly and preparation of equipment for installation and service.
Assists in the clean up, repair, and preparation for the next job.
Assists in Job Safety Analysis (JSA) and safety meetings.
Job tasks, correctly performed, have minimal impact upon the viability of the organization.
Error is readily ascertainable by the supervisor and can be corrected.
Promotes safety awareness and environmental consciousness, and complies with all applicable safety and environmental procedures and regulations.
Ensures compliance with Health, Safety, and Environmental (HSE) regulations and guidelines.
Promotes and takes an active part in quality improvement processes.
Skills are typically acquired by completing the career development requirements in iLearn's competency management system and 3- 6 months experience as an Operator Asst I.
Must have successfully passed company tests and met competency Task Lists requirements.
The ability to perform basic mathematical calculations is required.
Reading comprehension and writing skills are required.
Basic computer skills are needed.
Licensure to drive commercial vehicles is required for land operations.
Candidates having qualifications that exceed the minimum job requirements will receive consideration for higher level roles given (1) their experience, (2) additional job requirements, and/or (3) business needs. Depending on education, experience, and skill level, a variety of job opportunities might be available including Service Operator I to Service Operator II.
Halliburton is an Equal Opportunity Employer.
420 Halliburton Dr, Williston, North Dakota, 58801, United States
Requisition Number: 75160
Experience Level: Entry-Level
Job Family: Operations
Product Service Line: Production Solutions
Full Time / Part Time: Full Time
Additional Locations for this position:
Compensation is competitive and commensurate with experience.
Founded in 1919, Halliburton is one of the world's largest providers of products and services to the energy industry. With over 50,000 employees, representing 140 nationalities, and operations in approximately 70 countries, the company serves the upstream oil and gas industry throughout the lifecycle of the reservoir – from locating hydrocarbons and managing geological data, to drilling and formation evaluation, well construction, completion and production optimization. Halliburton's fascinating and proud history reveals a continuous focus on innovation and expansion that began with the company's founder, Erle P. Halliburton. After borrowing a wagon, a team of mules and a pump, he built a wooden mixing box and started an oil well cementing business in Duncan, Oklahoma.
In the 1930s, Halliburton established its first research laboratories where the company tested cement mixes, began offering acidizing services to break down the resistance of limestone formations and increase the production of oil and gas, and performed its first offshore cementing job using a barge-mounted cementing unit at a rig in the Creole Field in the Gulf of Mexico. This was the beginning of what was to become the world's most extensive offshore service.
Halliburton took the initial steps toward becoming a worldwide company in 1926. We sold five cementing units to an English company in Burma, the start of our Eastern Hemisphere operations, and Erle P. Halliburton sent his brothers to open our business in Alberta, Canada. We opened in Venezuela in 1940. By 1946, the company – using its innovative technology – had expanded into Colombia, Ecuador, Peru and the Middle East and began performing services for the Arabian-American Oil Company, the forerunner of Saudi Aramco.
In 1951, Halliburton made its first appearance in Europe as Halliburton Italiana SpA., a wholly owned subsidiary in Italy. In the next seven years, Halliburton launched Halliburton Company Germany GmbH, set up operations in Argentina and established a subsidiary in England.
In 1984, Halliburton provided all of the well completion equipment for the first multiwell platform offshore China. Two years later, Halliburton became the first American company to perform an oilfield service job on the China mainland
The final decade of the 20th century brought more changes and growth to Halliburton. The company opened a branch office in Moscow in 1991.
The company realigned its work into Eastern and Western Hemisphere operations in 2006, and in 2007, divided its service offerings into two divisions: Completion and Production, and Drilling and Evaluation.
Today, Halliburton offers the world's broadest array of products, services and integrated solutions for oil and gas exploration, development and production.
To learn more about career opportunities, please visit www.gohalliburton.com.
Halliburton is an equal opportunity employer.
Halliburton placed 2nd in the 2018 Rigzone Ideal Employer Rankings - find out more.